Clean and Disinfect Floors with Pine Power: Using Pine-Sol in Bissell CrossWave
Looking for an easy way to clean and disinfect hard floors? Using Pine-Sol in the Bissell CrossWave can help kill germs while leaving your floors sparkling clean. But there are some important things to know before mixing Pine-Sol into your CrossWave.
We'll cover proper dilution, using it to disinfect, cleaning different floor types, and important precautions. Follow along for tips that will get your floors pine-fresh clean.
Is Pine-Sol Safe for Use in the CrossWave?
While not recommended as a primary cleaning solution, Pine-Sol can be safely used in the CrossWave to occasionally disinfect and deodorize floors. However, it's important to always dilute Pine-Sol before use to avoid leaving too much sticky residue behind.
We recommend testing a diluted Pine-Sol solution in a small, inconspicuous area first. Check back in 20-30 minutes to see if any noticeable residue remains. If the floor remains streak-free, the solution can be used in the rest of the home.
The Benefits of Using Pine-Sol
When used properly, Pine-Sol offers these advantages:
- Disinfects floors by killing germs and bacteria
- Leaves a pleasant pine scent as it cleans
- Can cut through tough grime and buildup
- Deodorizes floors in high-traffic areas
How to Dilute Pine-Sol for the CrossWave
Always dilute concentrated Pine-Sol before pouring it into the CrossWave's solution tank. This helps minimize the risk of residue being left behind on floors.
We recommend starting with a dilution ratio of 1 part Pine-Sol to 4 parts water. For example, mix 1 cup Pine-Sol with 4 cups water. Shake well to fully incorporate.
For extra dirty floors, you can increase the Pine-Sol concentration slightly, using a 1:3 ratio. But never use full strength or residue may occur.
Tips for Diluting
- Always dilute in a clearly marked spare bottle
- Start with a weaker solution and adjust as needed
- Shake before each use to remix any separation
- Make fresh solution weekly for maximum effectiveness
Using Pine-Sol to Disinfect High-Traffic Areas
While not ideal as an everyday cleaning solution, Pine-Sol shines when used occasionally to disinfect high-traffic floors prone to germs, like in the bathroom and kitchen.
Aim to use diluted Pine-Sol in the CrossWave every 2-3 weeks to kill bacteria in these high priority rooms. It can provide an extra level of disinfecting power beyond regular floor cleaner.
Be sure to give special attention to sanitizing surfaces like:
- Around the toilet
- Under appliance doors
- Around cabinet handles
- entryways
Pine-Sol's antibacterial powers can help keep the whole family healthier.
Using the Right Cleaner for Different Floors
While great for disinfecting, Pine-Sol may not be the best choice for routine cleaning of all hard floor types. Consider these tips:
Sealed Hardwood Floors
Diluted Pine-Sol is safe for most modern, urethane-sealed hardwood when used occasionally. But overtime it could potentially dull the finish. Use the CrossWave's hardwood floor cleaner for daily washing.
Tile & Grout
Pine-Sol can help sanitize tile floors and grout lines. But you'll need a tile-specific cleaner or whitening product to really make them shine.
Vinyl & Laminate
These softer floors are prone to scuffs and scratches, so use a gentle, vinyl-safe cleaner daily unless disinfecting.
Important Precautions with Pine-Sol
While a proven cleaning and disinfecting product, Pine-Sol still requires these precautions:
- Never mix or combine with other household cleaners
- Use in a well-ventilated area
- Wear gloves to protect skin
- Keep out of reach of children and pets
- Always rinse floors after cleaning
Be sure to read and follow all label instructions when using Pine-Sol or any other cleaning product.
How to Use Pine-Sol in the CrossWave
Once you've created your diluted Pine-Sol solution, using it in the CrossWave is easy. Just follow these steps:
- Fill the solution tank with the diluted Pine-Sol mix
- Attach the correct brush head for your floor type
- Make sure the machine is set to Floors mode
- Work in sections across the floor, overlapping passes
- Rinse with plain water when finished to remove any residue
- Thoroughly rinse out tank when done before using a new solution
Be sure to give the Pine-Sol time to work by not rinsing immediately. And refer back to our dilution tips to get the perfect mix.
Frequently Asked Questions
Can I use Pine-Sol as my only cleaner?
No, Pine-Sol should be used sparingly to disinfect floors. Use the CrossWave's floor cleaners for routine washing.
Does Pine-Sol leave a film on floors?
When used diluted, it should not leave a noticeable film or hazy residue. Always test a small area first.
How often should I use Pine-Sol?
Aim to use it every 2-3 weeks for disinfecting high traffic areas prone to germs.
Pine-Sol can be a useful addition to your Bissell CrossWave when you need to tackle problem germs and grime. Just be sure to dilute it properly and rinse floors well after use. Refer to our tips to mix up a solution that leaves your floors fresh and residue-free.
You can keep floors clean and healthy with the CrossWave and Pine-Sol.